Free 52546.pdf - Indiana

OAQ PROCESS INFORMATION APPLICATION PI-06: Electroplating
State Form 52546 (R / 1-07)

INDIANA DEPARTMENT OF ENVIRONMENTAL MANAGEMENT

IDEM ­ Office of Air Quality ­ Permits Branch 100 N. Senate Ave., MC 61-53 Indianapolis, IN 46204-2251 Telephone: (317) 233-0178, or Toll Free: 1-800-451-6027 x30178 (within Indiana) Facsimile Number: (317) 232-6749 www.idem.IN.gov/permits/air/index.html

NOTES:

· · ·

The purpose of this form is to obtain detailed information about the electroplating process. Complete one form for each process unit (or group of identical process units). This is a required form. Detailed instructions for this form are available online at

www.idem.IN.gov/permits/air/apps/instructions/pi06instructions.doc .
All information submitted to IDEM will be made available to the public unless it is submitted under a claim of confidentiality. Claims of confidentiality must be made at the time the information is submitted to IDEM, and must follow the requirements set out in 326 IAC 17.1-4-1. Failure to follow these requirements exactly will result in your information becoming a public record, available for anyone to inspect and photocopy.

PART A: Process Information Part A identifies the electroplating process. If there are multiple process units that are identical in nature, capacity, and use, you may use one form to summarize the data for the identical process units. 1. Unit ID: 3. How many (identical) process units are identified in this form? One Hard Chrome 4. Type of Plating Process: Chromium Anodizing Nickel Other (specify): 5. Maximum Production Rate (specify units): 6. Add-On Control Technology: Identify all control technologies used for this unit, and attach completed CE-01 (unless "none"). None Wet Scrubber / Absorption ­ Attach CE-05. Other (specify): ­ Attach CE-10. 2. Installation Date:
(actual or anticipated)

More than one (specify number) : Decorative Chrome Cadmium Zinc

7. Control Techniques: Identify all control techniques used for this process. None Composite Mesh Pad Wetting Agent Fiber-Bed Mist Eliminator Foam Blanket Fume Suppressant

8. Process Limitations / Additional Information: Identify any acceptable process limitations. Attach additional information if necessary.

This space is intentionally left blank.

Continued on next page

Page 1 of 2

Indiana Department Of Environmental Management Office Of Air Quality State Form 52546 (R / 1-07)

Process Information ­ Electroplating FORM PI-06 Page 2 of 2

PART B: Emission Factors Part B identifies all emission factors used to calculate air emissions from this process. 9. Process Unit
(& ID, if applicable)

10. Air Pollutant

11. Emission Factor
value units

12. Source of Emission Factor
(if not using AP-42, include calculations)

AP-42 AP-42 AP-42 AP-42 AP-42 AP-42

Other Other Other Other Other Other

PART C: Process Tank Details Part C identifies the process tanks, the rectifier capacity and bath components of each tank, materials processed, raw material usage, and tanks under common control. 13. Process Tank 14. Rectifier Capacity (A) 15. Bath Components 16. Materials Processed 17. Raw Material Usage Rate (lb/hr) 18. Common Control? Yes Yes Yes Yes Yes Yes No No No No No No

PART D: Federal Rule Applicability Part D identifies any federal rules that apply to the process. 19. Is a New Source Performance Standard (NSPS) applicable to this source?
If yes, attach a completed FED-01 for each rule that applies.

Yes

No

40 CFR Part 60, Subpart

(Specify):

20. Is the National Emission Standard for Hazardous Air Pollutants (NESHAP) for Chromium Electroplating (40 CFR Part 63, Subpart N) applicable to this source?
Attach a completed FED-01 if this rule is applicable.

Yes

No

21. Non-Applicability Determination: Provide an explanation if the process unit appears subject to a rule (based on the rule title or the source category), but the rule will not apply.