OAQ PROCESS INFORMATION APPLICATION PI-07: Welding & Cutting of Metal
State Form 52547 (R / 1-07)
INDIANA DEPARTMENT OF ENVIRONMENTAL MANAGEMENT
IDEM Office of Air Quality Permits Branch 100 N. Senate Ave., MC 61-53 Indianapolis, IN 46204-2251 Telephone: (317) 233-0178, or Toll Free: 1-800-451-6027 x30178 (within Indiana) Facsimile Number: (317) 232-6749 www.idem.IN.gov/permits/air/index.html
NOTES:
· · ·
The purpose of this form is to obtain detailed information about the welding and cutting of metal. Complete one form for each process unit (or group of identical process units). This is a required form. Detailed instructions for this form are available online at
www.idem.IN.gov/permits/air/apps/instructions/pi07instructions.doc .
All information submitted to IDEM will be made available to the public unless it is submitted under a claim of confidentiality. Claims of confidentiality must be made at the time the information is submitted to IDEM, and must follow the requirements set out in 326 IAC 17.1-4-1. Failure to follow these requirements exactly will result in your information becoming a public record, available for anyone to inspect and photocopy.
PART A: Welding Information Part A identifies all the welding processes and the corresponding information for each process. If a component is not applicable, state N/A in the space provided. 1. Unit ID 2. Welding Method 3. Number of Stations 4. Installation Date 5. Type of Electrode Used 6. Maximum Consumption
(lb/hr)
PART B: Flame Cutting Information Part B identifies the flame cutting process and the information corresponding to the process. You may summarize the process units if they are of the same type, capacity, use, and installation dates. Use additional forms as necessary. 7. Unit ID 8. Type of Flame Cutting 9. Number of Stations 10. Installation Date 11. Maximum Metal Thickness Cut
(inches)
12. Maximum Metal Cutting Rate
(inches/min)
PART C: Emission Factors Part C identifies all emission factors used to calculate air emissions from the process units listed on this form. 13. Process / Unit ID
(Include all units listed above)
14. Air Pollutant PM PM-10
15. Emission Factor
value units
16. Source of Emission Factor
(if not using AP-42, include calculations)
AP-42 AP-42 AP-42 AP-42 AP-42 AP-42
Other Other Other Other Other Other
Continued on next page
Page 1 of 2
Indiana Department Of Environmental Management Office Of Air Quality State Form 52547 (R / 1-07)
Process Information Welding/Cutting of Metal FORM PI-07 Page 2 of 2
PART D: Emission Controls and Limitations Part D identifies the control technologies, techniques, and other process limitations corresponding to each process. 17. Add-On Control Technology: Identify all control technologies used for this unit, and attach completed CE-01 (unless "none"). Welding None Baghouse / Fabric Filter Attach CE-02. Cyclone Attach CE-03. Electrostatic Precipitator Attach CE-04. Other (specify):
Attach CE-10.
Flame Cutting None Baghouse / Fabric Filter Attach CE-02. Cyclone Attach CE-03. Electrostatic Precipitator Attach CE-04. Other (specify):
Attach CE-10.
18. Control Techniques: Identify all control techniques used for this process. Welding Flame Cutting
19. Process Limitations / Additional Information: Identify any acceptable process limitations. Attach additional information if necessary. Welding Flame Cutting
PART E: Federal Rule Applicability Part E identifies any federal rules that apply to the process. 20. Is a New Source Performance Standard (NSPS) applicable to this source?
If yes, attach a completed FED-01 for each rule that applies.
Yes
No
40 CFR Part 60, Subpart
(Specify):
21. Is a National Emission Standard for Hazardous Air Pollutants (NESHAP) applicable to this source? If yes, attach a completed FED-01 for each rule that applies. 40 CFR Part 61, Subpart 40 CFR Part 63, Subpart
(Specify): (Specify):
Yes
No
22. Non-Applicability Determination: Provide an explanation if the process unit appears subject to a rule (based on the rule title or the source category), but the rule will not apply.