Free Declaration - District Court of Delaware - Delaware

Case 1:04-cv-00343-JJF

Document 646-7

Filed 05/02/2007

Page 1 of 7

EXHIBIT F

Case 1:04-cv-00343-JJF
6

Document 646-7

Filed 05/02/2007

Page 2 of 7

LM151X1 LiquidCrystal Display Product General Specification

1. General Description
The LM151X1 LCD is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent Tube(CCFT) back light system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally white mode. This TFT-LCD has a 15.1 inch diagonally measured active display area with XGA resolution(768 vertical by 1024 horizontal pixel array). Each pixel is divided into Red, Green and Blue subpixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the subpixel color is determined with a 8-bit gray scale signal for each dot, thus, presenting a palette of more than 16,777,216 colors. LM151X1 has been designed to apply the interface method that enables low power, high speed low EMI. Panellink must be used as a LVDS(Low Voltage Differential Signaling) chip. The LM151X1 LCD is intended to support applications where high brightness, wide viewing angle, high color saturation, and high color depth are very important. In combination with the vertical arrangement of the sub-pixels, the LM151X1-D2MN characteristics provide an excellent flat panel display for office automation products such as monitors.

PanelLin k receiver

CN2 CN3

General Display Characteristics The following are general features of the model LM151X1 LCD; Active display area 15.1 inches(38cm) diagonal Outsize dimensions 352.6w * 264.6h * 16.0t(typ)m m(Without Inverter) Pixel pitch 0.30 mm 0.30 mm Pixel format 1024 horiz. By 768 vert. pixels RGB vertical stripe arrangement Color depth 8-bit, 16,777,216 colors Display operating mode transmissive mode, normally white Surface treatments hard coating(3H), anti-glare treatment of the front polarizer

Revision Ver 1.2

CN1 connector(21pin)

LVDS 4 pairs

Timing Control Block

1 1

Source driver circuit

Gate Driver

V sync H sync
V CC(3.3V) Power line for Digital logic Analog power line for TFT-LCD panel

TFT-LCD Panel ( 1 0 2 4 ×7 6 8 )

V DD(5V)

DC/D C Bloc

B a c k l i g h t A s s 'y

July 11, 2000

Page

1/ 6

Case 1:04-cv-00343-JJF
6

Document 646-7

Filed 05/02/2007

Page 3 of 7

LM151X1 LiquidCrystal Display Product General Specification

2. Electrical Specifications 2-1 Electrical Characteristics
The LM151X1 requires three power inputs. Two inputs are employed to power the LCD electronics and to drive the voltages to drive the TFT array and liquid crystal. And the third input which powers the backlight CCFL, is typically generated by an inverter. The inverter is an external unit to the LCD. Table1 ELECTRICAL CHARACTERISTICS: Values Symbol Min. Typ. Max. VDD VCC IVDD IVcc IVDD IVcc VBL IBL 4.75 3.15 685 3.0 1290 1660 Operating Frequency Life time FBL 30 25,000 5.0 3.3 360 230 585 8.0 50 40,000 5.25 3.45 500 300 1.2 0.6 570 9.0 880 1145 80 -

Parameter

Units VDC VDC mA mA A A VR M S mA VR M S VR M S VR M S VR M S KHz hours

Notes 1 2 3

MODULE: Power Supply Input Voltage Power Supply Input Current Power Supply Kick-Off Current BACK LIGHT Back light Input voltage Backlight Input Current Lamp Kick-Off Voltage

4
At 25 2 At 0 2

5
At 25 2 At 0 2

6 7

Notes: 1. VDD input is the analog power supply for the TFT array and liquid crystal, and V CC input is the digital logic power supply for the LCD electronics. 2. The input current shall be measured at VDD of 5.0Vdc at 25 , refresh rate of 60Hz, and clock frequency of 65MHz under 9 gray pattern. 3. Power supply kick off current means power supply input current at the moment of LCM power on. This current is higher then the current at the normal operating condition and it lasts for 50~100ms. 4. The backlight input current shall be measured at the ground cable and does not include loss of external inverter. 5. Voltages at both ends of the lamp. 6. Voltages at secondary side of transformer using the balancing capacitor, 22pF in inverter. These voltages can be changed with customer's own design of inverter. 7. The life time is defined as the time at which brightness of lamp is 50% compare to that of initial value at the typical lamp current on condition of continuous operating at 25 2 .

Revision Ver 1.2

July 11, 2000

Page

2/ 6

Case 1:04-cv-00343-JJF
6

Document 646-7

Filed 05/02/2007

Page 4 of 7

LM151X1 LiquidCrystal Display Product General Specification

2-2 Interface Connections
This LCD employs three interface connections, a 21 pin connector is used for the module electronics and two connectors, a three pin connector, are used for the integral backlight system. Interface chip as a transmitter, must be used Panellink ,part No. SiI100, designed by Silicon Image Inc. or equivalent. The electronics interface connector is a model FI-WE21P-HF manufactured by JAE. The pin configuration for the connector is shown in the table below. Table 2 MODULE CONNECTOR PIN CONFIGURATION Pin Symbol 1 GND 2 VDD VDD 3 VDD 4 GND 5 GND 6 GND 7 VCC 8 R2+ 9 R210 VCC 11 R1+ 12 R113 VCC 14 R0+ 15 R016 Hsync 17 18 RCL+ RCL19 Vsync 20 NC 21 Description System ground Analog power supply for TFT array and liquid crystal System ground System ground System ground Digital logic power supply Plus signal of channel 2 (PanelLink) Minus signal of channel 2 (PanelLink) Digital logic power supply Plus signal of channel 1 (PanelLink) Minus signal of channel 1 (PanelLink) Digital logic power supply Plus signal of channel 0 (PanelLink) Minus signal of channel 0 (PanelLink) Output pin of Hsync signal for the customer's usage Plus signal of clock channel (PanelLink) Minus signal of clock channel (PanelLink) Output pin of Vsync signal for the customer's usage No Connection Notes see Note 1 +5.0V +5.0V +5.0V see Note 1 see Note 1 see Note 1 +3.3V R0~R7,CLT2,DE, See Note 2 +3.3V G0 ~ G7, CLT0, CLT1, See Note 2 +3.3V B0 ~ B7, Hsync, Vsync ,See Note 2 see Note 3 Main Clock, See Note 2 see Note 3

Notes: 1. All GND(ground) pins should be connected to the LCD's metal frame. 2. Refer to the data sheet of PanelLink transmitter SiI100. 3. Pins for DPMS. When VCC is on, Vsync and Hsync are available. In case HSYNC output, sync width is always fixed about 1.1usec independent of HSYNC coming from VGA controller. TOP SIDE LEFT SIDE OF LCM BOTTOM SIDE The backlight interface connector is a model BHR-03VS-1, manufactured by JST. The mating connector part number is SM02(8.0)B-BHS-1-TB or equivalent. The pin configuration for the connector is shown in the table below. Table 3 BACKLIGHT CONNECTOR PIN CONFIGURATION Pin Symbol Description Notes 1 HV Lamp power input 1 2 NC No connect 3 LV Ground 2 Notes: 1. The input power terminal is colored pink. Ground pin color is light pink. Revision Ver 1.2 July 11, 2000 Page 3/ 6
PIN 1 PIN 2 PIN 21 PIN 20

Case 1:04-cv-00343-JJF
6

Document 646-7

Filed 05/02/2007

Page 5 of 7

LM151X1 LiquidCrystal Display Product General Specification

< Front View >

Revision Ver 1.2

July 11, 2000

Page

4/ 6

Case 1:04-cv-00343-JJF
6

Document 646-7

Filed 05/02/2007

Page 6 of 7

LM151X1 LiquidCrystal Display Product General Specification

< Rear View >

Revision Ver 1.2

July 11, 2000

Page

5/ 6

Case 1:04-cv-00343-JJF
6

Document 646-7

Filed 05/02/2007

Page 7 of 7

LM151X1 LiquidCrystal Display Product General Specification

3.PRECAUTIONS
The LCD Products listed on this documents are not suitable for use of Military,Industry,Medical etc. system. If customers intend to use these LCD products for above application, please contact ours sales people in advance.

Revision Ver 1.2

July 11, 2000

Page

6/ 6